Difference between revisions of "Installing OpenOCD"
From spiderboard.org
Line 60: | Line 60: | ||
Due to a hardware issue on the MX10, in order to get PIC JTAG programming through OpenOCD to work, one has to desolder four resistors on the module. | Due to a hardware issue on the MX10, in order to get PIC JTAG programming through OpenOCD to work, one has to desolder four resistors on the module. | ||
− | [[File:Mx10-resistors-to-remove.pdf | page=1 | left | 750px | thumb | One resistor on the top side of the module.]] | + | [[File:Mx10-resistors-to-remove.pdf | page=1 | left | 750px | thumb | One resistor on the top side of the module, marked with a red cross.]] |
− | [[File:Mx10-resistors-to-remove.pdf | page=2 | center | 750px | thumb | Three resistors on the bottom side of the module.]] | + | [[File:Mx10-resistors-to-remove.pdf | page=2 | center | 750px | thumb | Three resistors on the bottom side of the module, each marked with a red cross.]] |
Revision as of 09:52, 4 June 2019
Installing OpenOCD
- OpenOCD Version >= 0.10 with the libftdi driver is required.
- If your package distributor provides this version, use your package manager to install OpenOCD:
- For Debian based distributions the terminal command is:
- $ sudo apt install openocd
- If the package version does not work, it is possible to compile OpenOCD from source (github).
Shell Script For Easier Use
A shell script can be used that starts OpenOCD, runs the svf file and shuts down afterwards, allowing conveniently programming the FPGA using a single terminal command.
- Create the file mx10spider_prog under .local/bin in your home directory and insert the content below.
- If not already done, add .local/bin to the path variable.
- Open .profile in your home directory with a text editor and add the line:
- PATH=".local/bin:$PATH"
- Logout and login again or run the following command to reload the path variable:
- $ source ~/.profile
- Open .profile in your home directory with a text editor and add the line:
- Open a terminal and add the executable flag.
- $ chmod +x .local/bin/mx10spider_prog
- You are now ready to program the fpga using the command:
- $ mx10spider_prog <path/to/file.svf>
- If your project is for example located under /opt/quartus_projects/Example, use one of the following commands:
- $ mx10spider_prog /opt/quartus_projets/Example/output_files/Example.svf
- $ mx10spider_prog /opt/quartus_projets/Example/output_files/Example_pof.svf
- for programming the .sof or .pof file respectively.
mx10spider_prog:
#!/bin/sh me=$(basename $0) if [ -f "$1" ]; then openocd -c "interface usb_blaster" -c "usb_blaster_lowlevel_driver ftdi" -c "usb_blaster_vid_pid 0x04d8 0xefd0" -c "jtag newtap max10 tap -irlen 10 -expected-id 0x31810dd -expected-id 0x318a0dd \ -expected-id 0x31820dd -expected-id 0x31830dd -expected-id 0x31840dd \ -expected-id 0x318d0dd -expected-id 0x31850dd -expected-id 0x31010dd \ -expected-id 0x310a0dd -expected-id 0x31020dd -expected-id 0x31030dd \ -expected-id 0x31040dd -expected-id 0x310d0dd -expected-id 0x31050dd" -c "init" -c "svf $1 progress" -c "shutdown" elif [ "$1" = "" ]; then echo -e "\tError: No file specified.\n\tUsage: $me <file.svf>" elif [ "$1" = "-h" ] || [ "$1" = "--help" ]; then echo -e "\tUtility script to start openocd and run an svf file.\n\tUsage: $me <file.svf>" else echo -e "\tFile not found: $1\n\tUsage: $me <file.svf>" fi
MX10 Hardware Issue
Due to a hardware issue on the MX10, in order to get PIC JTAG programming through OpenOCD to work, one has to desolder four resistors on the module.